SKF INDUCTION HEATER UPTO 120KG

240v - User to fit plug top + Test & Tag
Stock Code:
TIH100M/230V
Price:
$6,876.24 incl GST

Description

High heating capacity of up to 120 kg bearing

The SKF medium induction heater TIH 100m has the same high standards of efficiency and

performance as the smaller heater TIH 030m, combined with increased capacity. The

advanced design of the power electronics allows features of accurate electric current control,

cut-outs to avoid overheating and controls on rate of temperature increase. 

Placing the induction coil outside the heater’s housing allows the heating of bearings weighing

up to 120 kg (264 lb). The heater is equipped with thermal overheating protection to reduce

the risk of damage to the induction coil and the electronics. In addition to temperature mode,

the TIH 100m is equipped with a time mode for heating components other than bearings.

The heater is supplied standard with three yokes and is available in two executions:

230V/50-60Hz or 400-460V/50-60Hz.

 
  • Standard swivel arm for large size yoke
  • Capable of heating a 97 kg (213 lb) bearing in less than 20 minutes, saving time and energy
  • 2-step power setting and smaller yokes allow heating smaller bearings safely and at lower power consumption

 

TECHNICAL DATA
Designation TIH 100m
SKF m20 performance 97 kg (213 lb)
Voltage, V/Hz- TIH 100M/230V230V/50-60Hz
- TIH 100M/MV400-460V/50-60Hz
Bearing:- Maximum weight120 kg (264 lb)
- Maximum bore diameter20 - 400 mm (0.8 - 15.7 in.)
Temperature control:- Range *0 - 250 °C (32 - 482 °F)
- Magnetic probeYes, K-type
- Accuracy (electronics)± 2 °C (± 3,6 °F)
Time control:- Range0 - 60 minutes
- Accuracy± 0,01 sec.
Performance example:- bearing, weight, temperature, time23156 CC/W33, 97 kg, 110 °C, 20m
Thermometer mode Yes
Bearing mode Yes
Power reduction 2-step; 50 - 100%
Demagnetisation according to SKF norms (automatic) Yes (<2 A/cm)
Can heat sealed bearings Yes
Can heat pre - greased bearings Yes
Error guiding codes Yes
Thermal overload protection Yes
Maximum magnetic flux 1,7 T
Control panel Key board with LED in remote control
Operating area (w × h) 155 × 205 mm (6.1 × 8.0 in.)
Coil diameter 110 mm (4.3 in.)
Dimensions (w × d × h) 570 × 230 × 350 mm (22.4 × 9.0 × 13.7 in.)
Total weight, including yokes 42 kg (92 lb)
Maximum power consumption 3,6 kVA (230V)
4,0-4,6 kVA (400-460V)
Number of standard yokes 3
Standard yokes 56 × 56 × 296 mm (2.2 × 2.2 × 11.7 in.), for heating bearings with bore diameter of 80 mm (3.1 in.) and larger
28 × 28 × 296 mm (1.1 × 1.1 × 11.7 in.), for heating bearings with bore diameter of 40 mm (1.6 in.) and larger
14 × 14 × 296 mm (0.6 × 0.6 × 11.7 in.), for heating bearings with bore diameter of 20 mm (0.8 in.) and larger
Core cross section 56 × 56 mm (2.2 × 2.2 in.)
Yoke storage Yes, foldable
Sliding arm No
Swivel arm Yes, large yoke only
Cooling fan No
Housing material Steel and glass filled polyamide
* Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact SKF for advice.

 

Stock Level:
Secondary Warehouse